prosesilver7

Patio Doors Repair – How to Fix a Wet Dog and Save Your Dog From Cold, Wet Feet Patio doors provide a comfortable and comfortable transition between your outdoor and indoor space. By keeping the air in your home, they can help you save money on heating or cooling bills. Over time the luster of your sliding glass or French door can fade. Fortunately, simple repairs can keep them looking and operating like new. Weatherstripping You're walking your dog to the park around 5 AM, and you end up into a puddle that is right next to your sliding patio door. You look around and see that the rain of last night was able to get through the patio door seals. Don't panic, this isn't going to be a simple task in five minutes. But with a little patience and a few tools to fix this, you can get it fixed and protect your dog from wet, cold feet. It is crucial to replace the weatherstripping that closes the gap between your door and jamb. This will stop drafts, pests and moisture. It also helps keep your energy bills lower. A quick inspection of your windows and doors will tell you whether the weatherstripping is in good condition or requires replacement. There are many types of weatherstripping, such as felt, open-cell foam, vinyl, thermoplastic rubber and metals like bronze or copper. Each has advantages and disadvantages. Foam with open cells and felt are cheap however they can be ineffective and visible when blocking airflow. Vinyl is more expensive but it holds up well and resists moisture. Rubber is a great material for high-traffic areas because it won't wear out as quickly. To install new weatherstripping, first remove the patio door from the frame by loosening the roller adjustment screws using a screwdriver. Then, with a flathead screwdriver, remove the plugs that secure the weatherstripping at the bottom of frame. Remove the weatherstripping you have previously removed from the frame and remove any adhesive remnants. Then, cut the new to the appropriate length, then peel back the plastic strip at one end and apply it to the jamb using a putty knife. After that, you can reinstall the door and re-adjust the roller screws to ensure that the door is in the track and shuts properly. Apply caulk that is waterproof where the stationary panel obstructs the sliding door and where the edge of the panel joins the frame. This is not as secure a seal than the weatherstripping but it should work for a time. Locks and Handles Patio door handles and locks are essential to the security of your home. Over time, they may become worn or damaged and require replacement. Additionally, the spindle that connects the exterior and interior handles could also require to be replaced. To replace a handle on a patio door, you must remove the old one first, unscrewing any screws holding it in the place. Once the old handle has been removed, use a level to ensure that the patio door is straight before installing the new handle. If the door is not straight, it could interfere with the lock and cause problems in the future. After you have the new handle installed, close and open it a few times to ensure it functions properly. If you have any issues, you should consult the manufacturer's guidelines or a hardware expert for assistance. To avoid problems in the future it is a good idea to also lubricate your lock mechanism using lubricant made of silicone. The most common patio door lock is the mortise latch. It's typically constructed of steel and is placed in a pocket that is cut into the door frame. They are usually used on sliding wood and aluminum doors. Before you purchase a new mortise lock, you need to measure. The measurements you require include the locations of the mounting holes as well as the position of the keyway in the lock. Some handles for patio doors have a built-in locking mechanism that's integrated into the handle. These handles feature an elongated key cylinder that is inserted into the handle's keyway. If you have this kind of patio door both the outside and inside locks are combined into one unit. This type of patio doors are typically found on sliding aluminum doors. If your patio door latch isn't fixed It could be due to the lock tongue isn't getting the jamb's hasp correctly. Another possibility is that the sliding door isn't completely parallel with the jamb on the side. Try opening the door for about an inch and spotting it against the frame to determine whether there is any gap between the door and the jamb. If there is, adjust the rollers on the bottom left or right of the patio door to get it in perfect alignment with the jamb. Misalignment Over time, the rollers and tracks of the door could lose their alignment. This could cause the doors to become stuck or difficult to move. This can also let drafts and cold air into your home, which can reduce the efficiency of your energy. Misalignment can be easily fixed and prevented. Simply applying a silicone-based oil to the rollers and tracks will make your doors glide smoothly again. This is a good idea in order to keep your doors running at their peak. Another issue that is common to patio doors is a ripped screen, which is a nuisance or even a safety risk. It may also hinder the doors from opening and closing correctly, which can result in energy loss. In some cases the damaged screen can be replaced, however in other cases, it's best to replace the entire door. If you're experiencing a tear in your screen, clean it thoroughly and try to avoid turning the handles of the door in the wrong way when you open and close the door. Hinges may loosen as time passes due to heavy use or wear and tear. Regularly tightening the screws will aid in resolving this issue and ensure your doors shut tightly. This is an easy task that can be done yourself, but if you're not confident doing it, you should consult a professional to ensure your doors are properly aligned and secure. You should also clean the rollers and tracks of your patio doors frequently. A simple vacuuming or brushing can remove dust and debris that might interfere with the smooth operation of your patio doors. You can also employ a special tool to clear away stubborn dirt or rust. It is possible to fix the misalignment by tightening or checking the screws. However, sometimes it is necessary to replace the hinges to ensure a durable seal. If your frames for your patio doors are sagging or warped, this can affect their alignment and performance. Shifting or warping can be caused by foundation changes however, it can also result from poor installation or repeated use. A professional can fix or replace your patio door frame and ensure it's aligned properly, allowing it to perform optimally. Rollers Patio doors that slide open are ideal for bringing the outside in and providing plenty of light, but they require some attention to ensure they are sliding smoothly. If you find that you have to really pull the handle to get your door to move, or it just doesn't slide as easily as it did in the past, the culprit may be the rollers. Over time the lower track may become clogged with dirt, sand, and mud that makes it difficult for the rollers to roll over. It is possible to clean it and spraying it with a lubricant like 2Slick. If the tracks have been cleaned and the rollers still don't glide freely it's time to replace the tracks. Replacement rollers are available for your door and track type. They are available at most hardware stores, but you'll need a friend to help with the removal and installation of the rollers. Before ordering replacements, get an image of the roller assembly installed within the door frame so that the experts can identify the exact model and the type you need. sliding patio door repair www.repairmywindowsanddoors.co.uk can also look for specific characteristics like bumps, dimples, flared edges and cut-outs which can narrow down replacement options. When the rollers are replaced then you'll need to install your sliding door in its frame. Get some help on this one since the door is very heavy. Check to see if there are any screws holding the track to either side of the frame. If so, make sure they are loose enough to allow the door's bottom to slide into the channel that is above the frame. Remove the screen door from the opening. Make sure it is free of the track rollers, track and track. Once the new rollers have been installed, carefully insert the door into the frame and then swing it into place. If the new rollers are adjustable you can adjust them to give the door clearance where it needs it.